Carling-Dhoot Portfolio

 


Click on the image to zoom

Hydraulic Control Panel


Control System for Tractor

 

AC Blower

 


TECHNICAL SPECIFICATIONS

• Voltage supply: 12 VDC

• Rated Current: 10A (max.)

• Contact Voltage drop at 10A - 150mV

• Insulation resistance at 500 VDC : 1M ohm min. (Terminal to Terminal)

• Operating Temperature : -40° to +85°C

• Mating Cycles (Insertion & Withdrawal of Charger) : 100,000 Cycles

• IP rating: IP40 protection

• Environmental specification: ROHS and ELV Compliance


Snap Action Switch (Plunger type)


TECHNICAL SPECIFICATIONS

• Voltage supply: 12 VDC

• Rated Current: 10A (max.)

• Contact Voltage drop at 10A - 150mV

• Insulation resistance at 500 VDC : 1M ohm min. (Terminal to Terminal)

• Operating Temperature : -40° to +85°C

• Mating Cycles (Insertion & Withdrawal of Charger) : 50,000 Cycles

• IP rating: IP67 protection

• Environmental specification: ROHS and ELV Compliance


 

Hazard Switch

 


TECHNICAL SPECIFICATIONS

• Voltage supply: 12 VDC

• Rated Current: 10A (max.)

• Contact Voltage drop at 10A - 150mV

• Insulation resistance at 500 VDC : 1M ohm min. (Terminal to Terminal)

• Operating Temperature : -40° to +85°C

• Mating Cycles (Insertion & Withdrawal of Charger) : 100,000 Cycles

• IP rating: IP67 protection (with  boot installed) above panel

• Environmental specification: ROHS and ELV Compliance

Push Button Switch

 




Push Switch is a momentary which is used for simple On/Off purpose. This switch is ideally suited for agriculture and construction sector.

TECHNICAL SPECIFICATIONS
• Operating Voltage Range: 9 To 16VDC
• Rated Voltage: 12 V, 2 Amp
• Operating Temperature: -40 C To + 85 C
• Switch Operating Force: 7 ~ 15 N.
• Contact Travel Distance: 0.5~1.2 Mm
• Maximum Travel: 2.7 Mm
• Switch Category: Normally Open
• Operation (I) Push - On (Ii) Push - Off
• Voltage Drop Before Endurance ≤ 20 Mv And After Endurance ≤ 100 Mv
• Electrical Contact System Protected Against Water And Dust According To IP67
• Endurance Life - 50,000 Cycles (1 Cycle Consist Of Push - On & Push - Off)
• Insulation Resistance Between Terminal To Terminal And Terminal To Body In Off  Position At 500VDC

Mobile Charging Socket

 



Mobile Charging Socket is designed to allow the charging of electronics in a vehicles. This socket receives the USB Charger through which different electronic appliances such as Mobile Phones, Tablets etc. can be Charged. In this socket, the base terminal acts as positive and the inner socket acts a negative, providing circuit polarity for USB Charger to be connected directly.

TECHNICAL SPECIFICATIONS

• Voltage supply: 12 VDC

• Rated Current: 20A (max.)

• Contact Voltage drop at 20A - 150mV

• Insulation resistance at 500 VDC : 1M ohm min. (Terminal to Terminal)

• Operating Temperature : -40° to +85°C

• Mating Cycles (Insertion & Withdrawal of Charger) : 100,000 Cycles

• IP rating: IP65 protection (with cap installed) above panel

• Environmental specification: ROHS and ELV Compliance

Multi Drive Mode Switch





Type of Switch - Keypad type
Rated Voltage - 5 V DC
IP Rating - IP 67
Switch Actuating cycles - 100000 Cycles
Switch Feedback - Tactile and audible
Function - Diesel saver, Normal & Power

Horn Switch


Horn switch for Tractor application

Technical Specifications
Voltage :- 12 VDC / 24 VDC
Current Rating :- 10 Amps
Temperature capacity :- -40 to 105 degree Celsius
Life Span - 100000 Cycles (Electrical and Mechanical)